View HLD15ZGE_1250173.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HLD SERIES - 60 WATT
Half-Brick
DESCRIPTION The HLD series are through-hole mount, Half-brick, Low profile, Dual output DC/DC high density converters. The HLD series provides onboard conversion of telecom and datacom input voltages to isolated low output voltages without the need for a heatsink. The HLD series is well suited for distributed power architectures, telecom equipment, and LAN/WAN and data process applications. FEATURES * Single-board, multi-layer design * Planar magnetics * Fully automated - minimal `touch time' * Two independently regulated outputs * Can start into high capacitive load * Low profile * Standard half-brick size and pinout
TECHNICAL SPECIFICATIONS
Input Parameter
Voltage Range 24 nom. 48 nom. Transient Voltage Withstand 24 nom. 48 nom. Turn-on Time Input Reflected Ripple Current Vin UVLO Window 24 nom. 48 nom.
Maximum
18-36 36-72 50/100 100/100 20 80 17/15 34/30
Unit
VDC
V/ms mS mApk-pk Von/Voff
General Parameter
Switching Frequency Remote ON/OFF Positive Negative (optional) Isolation Input-Output Temp. Coefficient On>3.5/Off<1.8 On<1.8/Off>3.5 1500 0.03 -40 to +100 -40 to +125 105-115 95 Pending 2 Oz. V V VDC %/ C

Maximum
300
Unit
KHz
Output Parameter
Setpoint Accuracy Line Reg. Vin min. - Vin max., Iout rated Output 1 Output 2 Load Reg. Iout min. - Iout max., Vin nom. Output 1 Output 2 Min. Output Current, each Output Dynamic Reg., 25% Loadstep Pk Deviation Settling Time Voltage Trim Range Power Limit Threshold Range OVP Trip Range 4 500 10 110-150 115-140 % Vout S % Pout rated % Vout %
90% 80%
Maximum
1
Unit
% Vout % Vout
Board Temp Operating Range Storage Range Thermal Shutdown Range Humidity max, Non-Condensing Safety C C C
0.2 1.0 0.5 1.0 1.0
%
% Vout A
Weight (approx)
Efficiency
70% 60% 50%
Vin = 36V Vin = 48V Vin = 72V
HLD15ZED
Notes
Specifications typically at 25C, nominal line, and full load unless otherwise stated. Specifications subject to change without notice. Patents Pending REV. 08/01
40%
Iout1 / Iout2 (A)
1
HLD SERIES - 60 WATT
Half-Brick
MODELS - (See the last page of section for options.)
MODEL INPUT VOLTAGE (VOLTS) INPUT VOLTAGE RANGE (VOLTS) MAXIMUM INPUT CURRENT (AMPS)* OUTPUT VOLTAGE (VOLTS) RATED OUTPUT CURRENT (AMPS)*** RIPPLE & NOISE pk-pk (mV) TYPICAL EFFICIENCY**
HLD15YGE HLD15YGB HLD15YED HLD15YEB HLD15ZGE HLD15ZGB HLD15ZED HLD15ZEB HLD15ZED-G****
NOTES: * ** *** ****
24 24 24 24 48 48 48 48 48
18-36 18-36 18-36 18-36 36-72 36-72 36-72 36-72 36-72
4.4 4.4 4.5 4.5 2.3 2.4 2.4 2.4 2.4
5.0/3.3 5.0/1.8 3.3/2.5 3.3/1.8 5.0/3.3 5.0/1.8 3.3/2.5 3.3/1.8 3.3/2.5
12/15 12/15 15/15 15/15 12/15 12/15 15/15 15/15 15/15
100/100 100/100 100/100 100/100 100/100 100/100 100/100 100/100 100/100
84% 83% 81% 81% 86% 85% 83% 83% 83%
Maximum input current at minimum input voltage, maximum rated output power. At nominal Vin, rated output. Current can be drawn from any single output to its maximum rated value, or from both outputs to a combined power level of 60W. -G overcurrent protection is latched; all other models hiccup.
MECHANICAL DRAWING
2.28 (57.9)
1.40 (35.56)
1
5 6
1.50 (38.10) 1.20 (30.48) 0.90 (22.86) 2.40 (61.0) 0.50 (12.70) 0.20 (5.08) 0.10 (2.54) 0.40 (1.02)
1.00 (25.40)
2
7
0.40 (10.16)
8 3 9
0
4
BottomView
10
0.50 (12.7) 1.90 (48.26) 0.19 (4.80) 0.18 (4.60) 0.50 (12.70) 0
Units inches (mm)
PIN
1 2 3 4 5 6 7 8 9 10
Function
-Vin No Pin Shutdown +Vin +Vout2 Vout2RTN Vout2 Trim +Vout1 Vout1RTN Vout1Trim
Tolerances
Inches: .XX 0.020 .XXX 0.010 Pin: 0.002 (Millimeters) .X 0.5 .XX 0.25
0.05
(Dimensions as listed unless otherwise specified.)
2
OPTIONS
When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table.
OPTION
Negative Logic Lucent-Compatible Terminal Strip Trim Enable Trim and Enable Current Share Headerless
SUFFIX
N T TS 1 2 3 4 Y
APPLICABLE SERIES
HAS, HBD, HBS, HES, HLS, HLD, LES, QBS, QES, QLS, TES, TQD HAS, HBD, HBS, HES, HLS, QBS, QES, QLS XWS, XWD, XWT IAS, LES IAD, IAS, LES, SMS IAS, LES SMS Encapsulated EWS, IWS, OWS
REMARKS
TTL "Low" Turns Module ON TTL "High" Turns Module OFF
Pin Length and Heatsink Options 0.110" (2.8mm) Pin Length 0.150" (3.8mm) Pin Length 0.24" (6.1mm) Horizontal Heatsink 0.24" (6.1mm) Vertical Heatsink 0.45" (11.4mm) Horizontal Heatsink 0.45" (11.4mm) Vertical Heatsink 0.95" (24.1mm) Horizontal Heatsink 0.95" (24.1mm) Vertical Heatsink 8 9 1H 1V 2H 2V 3H 3V All Units (Except SMS) All Units (Except SMS) All Units (All Units Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (All Units Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (All Units Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (All Units Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (All Units Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (All Units Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages)
Standard Pin Length is 0.180" (4.6mm)
Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad
Example Options: HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95" vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent-compatible trim and 0.110" pin length.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice.
3

▲Up To Search▲

Price & Availability of HLD15ZGE

	To Download HLD15ZGE Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .